Network Infrastructure

School WiFi and the DfE Standards: What to Specify Before You Buy

Seninix blog: school WiFi and the DfE standards — what schools and trusts should specify before buying a wireless upgrade.

If you are a school or trust about to spend money on wireless, there is one sentence in the government’s guidance worth reading before you read any supplier’s quote. The Department for Education’s wireless network core standard says that if you need an upgrade, you should ask for a solution that uses, at a minimum, the Wi-Fi 7 standard — and names it explicitly as Wi-Fi 7 (802.11be).

That matters because a great deal of the material written for schools still says Wi-Fi 6. If a proposal in front of you quotes Wi-Fi 6 as “the DfE standard”, it was written against older guidance, and that tells you something about how recently the supplier checked.

This post sets out what the standards actually require, in the order a buyer needs them, and flags the dependency that most wireless quotes leave out entirely.

“By 2030” does not mean a deadline in 2030

The wireless standard is one of six core standards, and the page says schools and colleges “should be working towards meeting it by 2030”. That is not a cliff edge, and anyone selling you one is overstating it.

What actually triggers the standard is written plainly: you should meet it when you need to upgrade an underperforming or unsupported solution. In other words, nobody is required to rip out working wireless. But the moment you do decide to replace it — because it cannot cope, or because the vendor has stopped supporting it — the standard applies to what you buy. That is the point at which specifying it properly costs nothing and getting it wrong costs for a decade.

What the wireless standard actually asks for

Four things, and only one of them is about the access points themselves.

1. The latest wireless standard

Wi-Fi 7 (802.11be) as the minimum for an upgrade. The guidance also tells you to look at something buyers rarely check: the network interface speeds of the access points, noting these will typically be 1Gbps, 2.5Gbps, 5Gbps or 10Gbps. That line is doing more work than it appears to. An access point capable of multi-gigabit throughput connected to a 1Gbps switch port is limited by the port, not the radio. It is a common and expensive way to buy capacity you never receive.

The standard also expects the network to be configured to support segregation and quality of service — so guest, staff, student and building-systems traffic are separated, and the things that suffer from delay are prioritised.

2. Coverage that matches how rooms are used

The guidance suggests access points across the site, “up to one per classroom”, with higher-specification units in high-capacity spaces such as halls. The requirement underneath is the important part: the number of access points should provide coverage in each space in line with the planned occupation level.

That is a capacity instruction, not a coverage one. Thirty devices in a classroom and three hundred in a hall are different problems, and an access point count derived from floor area will get both wrong. We have written separately about telling coverage and capacity apart, because it is the single most common reason a wireless upgrade disappoints.

Note also what the guidance asks you to design around: the impact from building management systems and other networks. In a school that means the neighbouring school, the CCTV, the door entry and whatever the site team installed in the plant room.

3. Central management

The management requirements are more specific than most people expect, and they are worth reading as a procurement checklist. The solution should provide active signal management and load balancing; deliver software security updates automatically as soon as they are available, with manual checks as well; include manufacturer warranty, licences, firmware and security updates; include a manufacturer-approved system administrator training package; be scalable for higher bandwidth later; and be capable of producing a configuration file that allows the solution to be reset to the original configuration.

That last one is quietly the most valuable. It is the difference between a network your team can restore and a network only the installer understands.

4. Security against unauthorised access

Straightforward in principle, and it connects to the separate filtering, monitoring and cyber security standards. In practice it is where segregation earns its place: devices that are not managed by the school should not be sharing a network with those that are.

The DfE asks for heat mapping. Ask for it in writing

Buried in the coverage requirement is a sentence worth quoting back to any supplier: the design “should include using wireless heat mapping as part of initial planning“.

Initial planning. Not afterwards, not as an optional extra, and not as a validation exercise once the access points are already on the ceiling. If a quote arrives with an access point count and no indication that anyone has modelled or measured the building, that is a reasonable thing to query — the guidance expects it as part of the design, and it is the step that determines whether the count is right.

A survey at design stage does something a spreadsheet cannot: it tells you what the walls, the neighbours and the room occupancy actually do to the signal in your building, before anything is bought.

The dependency most wireless quotes leave out

Here is the sentence that catches budgets out. The DfE’s network cabling standard says you should meet it when you replace underperforming cabling, in new building projects, or when you upgrade your wireless network.

So the cabling standard is not a separate project you can defer. By the government’s own logic, upgrading the wireless pulls it into scope. And it is specific:

  • Copper cabling should be Category 6A, with U/FTP recommended as a minimum
  • Compliance with British Standards 6701, 50173 and 50174
  • The installed permanent link should be no greater than 90m
  • No intermediate splices or patch panels in the cable runs, and the minimum bend radius respected both during and after installation
  • Fire rating to the current BS 6701 requirement, stated as Euroclass Cca s1b.d2.a2
  • Patch leads of the same type and standard as the installed cable, from the same manufacturer
  • Optical fibre of at least 16-core multimode OM4 between server and hub rooms

If a wireless quote does not mention cabling at all, it is worth establishing early whether the existing cabling meets this — because the answer determines whether the project is one job or two. More on what that work involves on our structured cabling page.

Questions worth asking any supplier

  • Which Wi-Fi generation are you quoting, and when did you last check the DfE standard?
  • What network interface speed do these access points need, and do our switch ports provide it?
  • How did you arrive at the access point count, and what occupancy did you assume per room?
  • Has anyone heat-mapped the building as part of this design? Can we see it?
  • Does our existing cabling meet the Cat 6A standard, and has it been tested — or are we assuming?
  • Will we get a configuration file that lets us restore the system ourselves?
  • What is included for firmware and security updates after handover, and for how long?

None of these are difficult questions for a supplier who has done the work. The answers tell you a great deal about the ones who have not.

A note on funding

Connect the Classroom funds wireless upgrades for eligible schools, but it works by invitation: the DfE identifies schools and contacts them directly, rather than schools applying. If you have been contacted, the useful thing to know is that the school still procures its own supplier — the funding does not choose one for you, so the questions above still apply.

Worth checking the current GOV.UK guidance directly rather than relying on a supplier’s summary of it, including ours. These pages change, and the wireless standard was rewritten relatively recently.

Where we fit

We are a London networking firm, not an education specialist, and we hold no framework place — so if your trust requires one, we are not your route. What we do is the technical half: measuring a building properly before anyone specifies hardware, designing wireless against the occupancy a space actually has, and installing the cabling it depends on.

If you are weighing up a wireless upgrade and want a second opinion on a specification before you commit, that is a conversation worth having early rather than after the order.

Quotations in this article are from the Department for Education’s wireless network core standard and network cabling standard on GOV.UK, read on 3 November 2026. Guidance changes — check the current pages before relying on it. Seninix is not a Connect the Classroom supplier and holds no procurement framework place. Free survey terms apply: seninix.com/terms.

Not sure where your network stands?

A free 30-minute infrastructure review. We look at what you are running, what it is being asked to do, and where the risk sits. No obligation.

Book your free review
WhatsApp us